Thursday, December 13, 2012

How Large An Area Will A Masonry Heater Heat?


By Doug Hargrave

At first glance this seems to be a simple question which should have an easy answer. In actuality the answer to this question is much more complicated. There are two factors that must be quantified in order to determine if a particular masonry heater design will heat a defined square foot area.  One factor, which is relatively easy to determine, is the maximum heat output of the masonry heater. The other factor, determining the heat load (loss) of a defined square foot area under the coldest conditions, is more difficult.
While it is difficult to make an accurate claim as to the amount of space a particular masonry heater design will heat, it is possible based on the amount of wood burned, to accurately predict its BTU output and to define its heat storage capacity.  On the other hand, determining the heat load of a home requires a heat loss calculation of the floors, walls and ceiling based on their insulation properties, a determination of the homes efficiency in terms of outside air infiltration and inside leaks, and finally the heat load must be adjusted to the heating degree days for the geographic location of the home.
The following question and responses recently appeared on the members chat forum for the Masonry Heater Association of North America.
Question:

What can you expect out of a masonry heater with (the home) insulation being average to slightly above average? It would be nice to know how many Btu’s or how many square feet a typical heater will take care of.
 
Respondent A

That is a loaded question, and you can get into a lot of trouble promising a customer to heat xx square feet. We have one heater heating a 2800 sq. ft. super-insulated house in a cold climate. An identical one was built in a milder climate, and is incapable of heating a 1000 sq. ft. "poorly insulated" house. "Insulated" is a misnomer, since leakiness is often a bigger factor than insulation. "Efficiency" would be a better term, or "low energy" or even better "low heating load". 
 
You are better off to quote the heat output of the heater, and leave it be the client's responsibility to determine how much of his heating load it will cover. You can also quote some magic voodoo stuff about radiant heat. While real, it is much harder to quantify.  The generally accepted maximum output of a large heater is 20,000 BTU/hr, or 6 kW. One of those cube shaped 220V shop heaters is about 5 kW, so imagine one of those blowing continuously.  To get 20,000 BTU/hr, you need to burn about 100 lbs of 20% moisture wood at 70% efficiency. Typically, that will be two 50 lb fires per day. If you try to build a heater larger than that, you really need to know what you are doing, or be guaranteed durability problems.  Some companies up the rating of their heaters by specifying 3 fires per day. So you'd get 20,000 BTU/hr with a 33 lb capacity firebox.

Respondent B

(Respondent A) is correct: The only thing you can safely guarantee is output. If the heater is planned as the major heat source, I ask people to provide heat loss statement to compare with heater's output. I also can give them rough assessment of heater's capabilities bases on the max output for a reasonably largest possible heater at 25000 Btu/hr, extreme cases, 30000btu hr, and on rule of thumb for heat loss per sq ft related to the estimated R-value of their outside walls. The numbers for this rule of thumb were given at least a couple of times in this forum in the past. Super insulated home (R30 walls +) will have heat loss of 10Btu per sq ft or less, while a century home without any insulation may be in 40-50 Btu per sq ft.

Respondent A (additional comments)

Super insulated home (R30 walls +) will have heat loss of 10Btu per sq ft or less, while a century home without any insulation may be in 40-50 Btu per sq ft.

Using this rule of thumb, for a 20,000 BTU/hr heater:  Super insulated house: 2,000 sq. ft.  Un-insulated century house: 400 sq. ft.  You also have to factor in location.  Ottawa Canada has 8,100 heating degree-days.  Vancouver has 4,700.  A house in Ottawa with 2,000 sq. ft. is equivalent to 3,500 sq. ft. in Vancouver or 1,150 sq. ft. in Fairbanks AK in terms of heating load.
Respondent C

Generally speaking more mass means more heat capacity. Not all houses are constructed equally or in the same geographic location and not everyone burns their heater the same. Also not all heaters are placed in a central location, so the buyer must be informed that the rating may be reduced based on location.  I always tell potential buyers that no matter what, "they will always have a zone of comfortable heat output" if the power goes out. 
 
Respondent D

To be on the safe side, it is a good idea to ask the home owner to have an energy audit done on their house.   These audits are not expensive and will show where the cold spots are in the house. On the blower test, the inspector can determine the square footage of air leaving the house through leaks and can show where the leaks are. This is money well spent and will have a lifetime of positive effects.
Respondent A: +Norbert Senf – Masonry Stove Builders, Shawville, Quebec
Respondent B: +Alex Chernov – Stovemaster, Caledon, Ontario
Respondent C: +Doug Hren – Masonry Heater Design House, Hickory Corners, Michigan
 
Respondent D: +Gary Hart – Aaron’s Ltd. Alternative Energy, High Ridge, Missouri
 

4 comments:

  1. Great articles on heating, I know that it is important in Lethbridge.

    ReplyDelete
  2. Nice article on heaters and its good features that a good heater should have. I like it.

    heater patio

    ReplyDelete
  3. Excellent blog! I really love reading on this blog the idea you share will capture my interest to visit your site more often. Please keep on posting.

    Heating contractor Toronto

    ReplyDelete
  4. Finally the best article I have read. Keep writing these amazing article. I love them.

    Heating and Cooling Brampton

    ReplyDelete

All posts are moderated. Please don't bother spamming or sending ads for anything because they will be deleted. We encourange comments about the use of masonry heaters from anyone.